Disclosure: As an Amazon Associate, we earn from qualifying purchases. If you click a link on this page and make a purchase, we may receive a small commission at no extra cost to you.
Honcaring UV Resin Kit 200g Review
Small UV resin projects can turn sticky, cloudy, or uneven when the resin layer is too thick or the curing light cannot reach the whole piece. The Honcaring UV Resin Kit 200g with UV Light combines two 100g bottles of ready-to-use hard-type resin with an 8W lamp and basic work-surface accessories. It is designed for jewelry, charms, pendants, and shallow keychains rather than deep pours. This review explains where the starter setup helps, what you still need to buy, and which curing limits matter before you order.
Quick Verdict
Rating: 8/10
Best For: Beginners making thin, small UV resin jewelry, charms, pendants, and keychains.
Bottom Line: You get 200g of ready-to-use resin, an 8W curing light, and a few practical starter tools in one compact kit. The tradeoff is limited support for thick pieces, dark pigments, and complete projects because molds and decorative supplies are not included.
| Specification | Detail |
|---|---|
| Brand | Honcaring |
| Model | UV Resin Kit 200g with UV Light |
| Product Type | Ready-to-use hard-type UV resin starter kit |
| Resin Quantity | 200g total, supplied as two 100g bottles |
| Listing Unit Count | 6.7 fluid ounces |
| Curing Light | 8W UV resin light |
| Included Accessories | Two silicone cups, two disposable gloves, and one blue silicone mat |
| Listed Package Dimensions | 5.5 x 2.4 x 6.1 inches |
| Best Use | Thin jewelry pieces, earrings, pendants, charms, and shallow keychains |
| Not Included | Molds, bezels, pigments, tweezers, polishing tools, and decorative inserts |
| Safety Note | Use gloves, work with ventilation, avoid contact with uncured resin, and follow the product label. |
What Is the Honcaring UV Resin Kit?
The Honcaring UV Resin Kit 200g with UV Light is a compact starter set for small crafts that cure under UV light. Unlike two-part epoxy, the resin is ready to dispense, so you do not need to measure resin and hardener or calculate a mixing ratio.
The package combines two 100g resin bottles with an 8W light, silicone cups, disposable gloves, and a silicone mat. That setup covers dispensing, basic pigment mixing, hand protection, and minor drips, but it does not give you molds or the decorative materials needed to finish a project.
The kit makes the most sense when UV light can reach the resin from the top, sides, or through a clear mold. It is less suitable for large castings, deep opaque molds, or designs filled with heavy dark pigment.
Who Should Buy It?
Best For
- Beginners who want resin and a curing light in the same package.
- Jewelry makers working with shallow bezels, earrings, pendants, and charms.
- Crafters who prefer a fast, ready-to-use resin for small batches and test pieces.
Skip If
- You plan to cast large, deep, or opaque pieces that block UV light.
- You need a complete craft bundle with molds, colors, bezels, and finishing tools.
- You regularly use dark pigments or layered designs that may need a stronger lamp.
Before You Buy: The included 8W light is intended for small, thin pieces. A thick layer, dark pigment, or opaque mold can prevent light from reaching the center and may leave soft or sticky areas.
Feature-by-Feature Review
Ready-to-Use Resin Format
The resin comes ready to dispense, so your setup is simpler than a two-part epoxy workflow. You can add a small amount to a bezel or shallow mold, arrange an insert, and cure the piece without weighing or stirring two components.
The two-bottle format is practical for storage because you can work from one 100g bottle while keeping the other closed. Keep both bottles away from direct sunlight and close the cap promptly, since stray UV exposure can begin curing material near the opening.
8W UV Light
The included 8W light removes the need to buy a lamp before your first project. It should suit thin, clear layers where the light can reach the full resin surface. You may need to rotate a piece or cure it from more than one side when the mold shape creates shaded areas.
The lamp is the kit’s main limitation as your projects grow. Deep molds and heavily colored resin demand more light penetration than a basic starter lamp can provide, so a stronger or larger curing setup may become a later upgrade.
Clear, Hard-Type Finish
The resin is presented as a clear, hard-type formula for jewelry and small decorative work. That type of finish is useful when you want dried flowers, glitter, stickers, or small charms to remain visible after curing.
A clear formula does not remove the need for careful technique. Dust, trapped air, fingerprints, moisture, and uneven exposure can still affect the surface. Clean tools and thin layers have a larger effect on the final result than rushing the pour.
Starter Accessories
Two silicone cups let you separate small tinted batches or hold decorative materials during a project. The blue silicone mat protects a limited work area from drips, while the two disposable gloves give you basic protection for an initial session.
You will still need project-specific supplies. Shallow molds or bezels, transparent pigments, toothpicks, tweezers, tape, decorative inserts, and a dust cover are common additions. The kit is a resin-and-light starter set, not a complete jewelry-making station.
How to Use It Correctly
Prepare a clean, dry, well-ventilated workspace before opening the resin. Put the silicone mat under your project, wear gloves, and keep uncured resin away from your skin, eyes, food areas, children, and pets. Follow the bottle label and lamp instructions for handling and curing.
Pour or spread a thin layer first. Check for bubbles, position your decorative pieces, and cure before adding the next layer. Layering takes longer than one thick pour, but it gives the 8W light a better chance to reach the resin evenly.
Use color sparingly. Transparent UV resin pigments allow more light through than dense, opaque colors. When a piece stays sticky, reduce the layer thickness, cure from another angle, and confirm that the pigment and mold are suitable for UV resin.
Let a cold bottle return to room temperature before use rather than applying direct high heat. A more fluid resin is easier to spread and may release bubbles more readily. Keep the cap and nozzle clean so cured residue does not interfere with later use.
Pro Tip: Test your mold, pigment, and curing time with one small sample before making a full batch. A test piece shows whether light reaches the center and helps you avoid repeating a sticky result.
Before You Use It: Safety and Storage
Uncured resin requires careful handling even when a product is described as low odor. Wear gloves, avoid direct skin and eye contact, and use the kit where fresh air can circulate. Stop using the product and follow the label guidance if you notice a leak, damaged container, or unusual reaction.
Children should not handle uncured resin or operate the curing light without close adult supervision. Store both bottles upright, tightly closed, and away from sunlight, heat, food, and pet access. Do not reuse resin-contact tools for food preparation.
Keep the UV light directed at the workpiece and follow its instructions. Do not stare into the light or expose skin unnecessarily. The kit is for crafts, not for dental, cosmetic, food-contact, or medical applications.
How It Performs in Real Use
For Earrings, Pendants, and Open Bezels
Thin jewelry pieces are the best match for this kit. Open bezels and shallow molds expose more resin to the 8W light, making it easier to cure each layer. The two 100g bottles also give you enough material to practice before using valuable decorative inserts.
For Keychains and Shallow Molds
Small keychains work when the mold is transparent and not too deep. Cure in stages, then turn the piece over after demolding if the underside needs more exposure. A thick single pour is more likely to trap bubbles or leave an uncured center.
For Embedded Flowers, Glitter, and Charms
Clear resin helps decorative inserts remain visible, but lightweight pieces can shift or float. A thin cured base layer gives you a stable surface for placement. Add the final covering layer only after the insert stays where you want it.
For Colored and Layered Designs
Transparent tints are easier to cure with a small lamp than heavy opaque pigments. Build color gradually and cure each layer before adding more. Complex designs can work, but they require more testing and patience than simple clear pieces.
Pros and Cons
Pros
- Includes 200g of resin split between two 100g bottles.
- The 8W light lets you begin small projects without buying a lamp separately.
- Ready-to-use resin avoids measuring and mixing two epoxy components.
- Silicone cups, gloves, and a mat cover basic setup and spill control.
- Well suited to thin jewelry, charms, pendants, and shallow keychains.
Cons
- The 8W lamp is not ideal for large, deep, or heavily pigmented pieces.
- Molds, pigments, bezels, tweezers, and finishing tools are not included.
- Good results still require thin layers, correct positioning, and trial and error.
Is It Worth the Price?
The Honcaring kit offers strong value for the price when you need resin, a basic light, and a few starter accessories in one order. It is especially useful for a beginner who does not already own a UV lamp and wants to test small jewelry projects before building a larger craft setup.
The value becomes weaker when you need a complete project bundle. You must supply the molds, bezels, colors, decorative inserts, and finishing tools, and you may eventually replace the 8W lamp if you move into larger or darker designs.
This is a smart buy for small, clear projects and short craft sessions. It is not the best fit for deep casting, production-scale batches, or buyers who want every tool included.
How It Compares to Alternatives
Similar starter kits from LET’S RESIN and KISREL are worth comparing when you want a different lamp shape, a broader accessory bundle, or more resin options. Check the current package contents carefully because lamps, bottle sizes, and included tools can vary between listings.
The Honcaring kit makes the most sense when you value the two-bottle 200g format, a compact 8W light, and a simple set of silicone accessories. A larger all-in-one kit may suit you better when molds and pigments matter more than a compact setup.
Common Problems and Troubleshooting
| Problem | Likely Cause | What to Try |
|---|---|---|
| Sticky surface | Layer is too thick or light cannot reach it | Use thinner layers and cure from another angle |
| Visible bubbles | Fast pouring, cold resin, or trapped air | Let resin reach room temperature and remove bubbles before curing |
| Uneven color | Pigment is too dense or not mixed evenly | Use less compatible pigment and test a small batch |
| Cloudy finish | Moisture, dust, or contaminated tools | Clean and dry the workspace, mold, and inserts |
Frequently Asked Questions
Can I use the Honcaring UV Resin Kit for crafts besides jewelry?
Yes. It can suit small charms, decorations, shallow keychains, and similar DIY pieces. The project should be thin enough for UV light to reach the resin fully.
Does the kit include a UV light?
Yes. The 200g kit includes an 8W UV resin light, so you can cure small projects without buying a separate starter lamp.
Do I need to mix resin and hardener?
No. This is ready-to-use UV resin rather than a two-part epoxy system. You can dispense it directly, add compatible decorations or pigment, and cure it with UV light.
Why does the resin stay sticky after curing?
A thick layer, dark pigment, shaded area, or opaque mold can block the light. Use thinner layers, cure from more than one direction, and test the mold and pigment before making a full batch.
Can I add color pigments?
Yes, but use a compatible pigment in a small amount. Transparent tints usually allow more UV light through than dense or opaque colors.
Are molds and jewelry findings included?
No. The listed package includes resin, the 8W light, silicone cups, gloves, and a silicone mat. You need to supply molds, bezels, findings, pigments, and decorative inserts.
Is the Honcaring UV Resin Kit safe for children?
Children should not handle uncured resin or the UV light without close adult supervision. Use gloves, provide ventilation, prevent skin and eye contact, and follow the product label.
How should I store unused UV resin?
Close the bottles tightly and store them upright in a cool, dry place away from sunlight and heat. Check the bottle label for the maker’s shelf-life and disposal guidance.
The Bottom Line
The Honcaring UV Resin Kit 200g earns an 8/10 for beginners who want a compact resin-and-light setup for thin jewelry and small crafts. Its main strengths are the two 100g bottles, ready-to-use format, and included 8W lamp, while its main limits are the basic light and missing molds and pigments. Skip it for deep pours or heavily opaque designs, but consider it for clear pendants, charms, earrings, and shallow keychains.
Ready to Buy?
Check the latest price, package contents, and product details before you decide.
