โœจ Trusted reviews and recommendations across tech, lifestyle, and more
Welding Accessories

MIG Welding Contact Tips 15AK Review

๐Ÿ“… March 18, 2026 ๐Ÿ‘ค Adrian Blake โฑ 14 min read ๐Ÿ’ฌ 0 comments
mig welding contact tips

Disclosure: As an Amazon Associate, we earn from qualifying purchases. If you click a link on this page and make a purchase, we may receive a small commission at no extra cost to you.

By Editorial Team ยท Reviewed for accuracy ยท Last updated October 2026

A worn MIG contact tip can cause poor wire feeding, unstable electrical contact, and extra welding downtime. The Welding Knight MIG Welding Contact Tips 15AK 11-35 provide 30 copper replacement tips sized for 0.035-inch (0.9 mm) welding wire. Their M6 threading and roughly 24 mm length make them worth considering for compatible MB15/15AK and selected Lincoln and Tweco welding guns. This review explains their specifications, fit requirements, practical benefits, and limitations so you can decide whether this pack suits your setup.

Quick Verdict

Rating: Recommended with compatibility checks

Best For: MIG welders using 0.035-inch wire who need a bulk supply of compatible M6 contact tips.

Bottom Line: The Welding Knight 30-pack offers a convenient supply of copper tips with clearly stated dimensions. Its main limitation is fit: you must confirm your gun’s contact-tip type, thread, and length before ordering.

Check Price on Amazon โ†’

Key Specifications at a Glance

SpecificationDetail
BrandWelding Knight
Product designation15AK 11-35
Product typeReplacement MIG/MAG welding contact tips
Wire diameter0.035 inch (0.9 mm)
Tip lengthApproximately 24 mm (0.945 inch)
ThreadM6, as stated in the listing
MaterialCopper
Package quantity30 contact tips
Listed compatibilityMB15/15AK MIG/MAG torches, Lincoln Magnum 100L, Tweco No. 1/Mini, and selected 11-series systems
Intended applicationCompatible MIG/MAG welding with 0.035-inch wire
Amazon ASINB0CQR6J3HQ
Return information30-day refund or replacement terms displayed on Amazon at review time, subject to applicable conditions

What Are the Welding Knight 15AK Contact Tips?

The Welding Knight 15AK 11-35 tips are consumable parts for compatible MIG welding guns. A contact tip guides the electrode wire through the torch and transfers electrical current to it. Because the wire moves through the tip during welding, this small component plays a direct role in arc stability and wire feeding.

Each package contains 30 copper contact tips for 0.035-inch wire. The listing identifies an M6 thread and an approximate 24 mm overall length. These details help you compare the pack with the contact tips already installed in your gun.

The main reason to buy this set is convenience. Instead of purchasing a replacement each time a tip becomes worn or damaged, you can keep multiple spares near your welding station. However, these are replacement consumables, not a complete torch repair kit.

Key Takeaways

  • 30-piece package: Useful for keeping spare contact tips ready during regular welding work.
  • 0.035-inch wire size: Designed for the stated 0.9 mm welding wire diameter.
  • Copper construction: Provides the electrical conductivity needed to transfer welding current to the wire.
  • M6 threading: Requires a matching threaded gas diffuser or contact-tip holder.
  • Approximately 24 mm long: Check this measurement against your original tip, since similar-looking replacements may differ.
  • Multiple claimed gun fits: Includes MB15/15AK and selected Lincoln and Tweco guns, but compatibility should be checked for your exact torch.
  • Important limitation: These are standard copper replacement tips, not a substitute for special-purpose contact tips when your welding setup requires them.

Product Features and Specifications

Copper Construction and Electrical Conductivity

Contact tips need good electrical conductivity because they transfer current to the moving electrode wire. Welding Knight uses copper for these tips, a common material in MIG welding consumables.

Good electrical contact helps your welding system deliver current through the wire. However, copper tips are still wear items. Heat, friction, spatter, and burnback can damage them over time.

The listing describes the material as wear-resistant and suitable for welding heat. It does not establish a specific service life or a measured improvement over genuine manufacturer tips.

0.035-Inch Wire Size and Tip Geometry

The 11-35 designation identifies the listed 0.035-inch welding wire size. This is the wire the tip is intended to accommodate, not a claim that the internal opening measures exactly 0.035 inch.

A contact tip needs enough clearance for the welding wire to move while maintaining electrical contact. If the tip is too small, wire feeding may become difficult. If the opening is too large for the application, electrical contact may become less consistent.

Choose your contact-tip size using the welding wire diameter and your gun manufacturer’s recommendations. Do not select a tip based only on its outside appearance.

M6 Threading and 24 mm Length

Welding Knight lists an M6 threaded connection and an approximate overall length of 24 mm. Both measurements matter when you replace a contact tip.

The thread must match the gas diffuser, while the tip length affects how the tip sits inside the nozzle. A tip that is too long or too short may change the intended contact-tip position.

Some standard Tweco 11-35 contact tips are listed at 25.4 mm overall length. That difference makes it wise to compare the actual replacement with the part required by your specific gun.

30-Piece Package for Routine Replacement

A 30-pack is useful when you weld often, train new operators, or maintain several compatible MIG guns. You can keep a few tips ready without interrupting work to order small replacement quantities.

Every listed tip uses the same 0.035-inch wire specification. This package is not a mixed-size assortment.

If your shop uses several wire diameters, you will still need correctly sized tips for those other wires.

Compatibility and Performance

The Welding Knight listing names MB15/15AK MIG/MAG torches, Lincoln Magnum 100L guns, and Tweco No. 1/Mini guns among its intended applications. It also refers to compatible 11-series contact-tip systems.

These compatibility claims are useful starting points, but you should confirm the exact part required by your gun. Gun model names alone may not tell you whether every torch configuration uses the same consumable.

The right contact tip must match your wire diameter, threaded connection, and gun’s required tip dimensions. A shared wire size does not guarantee a correct fit.

What to Check Before Ordering

  • Wire diameter: Confirm that your machine is currently set up for 0.035-inch wire.
  • Tip thread: Make sure your diffuser accepts the listed M6 threaded tip.
  • Tip length: Compare the original part with the listed 24 mm length.
  • Consumable series: Check your gun manual or the number on the existing replacement tip.
  • Gun configuration: Confirm that the nozzle and diffuser work with the replacement’s shape and installed position.

Before You Buy: Do not assume every 15AK, Lincoln Magnum 100L, or Tweco gun uses interchangeable contact tips. Verify the original part number, M6 thread, and required tip length. If you cannot confirm the fit, choose a replacement specified by your gun manufacturer.

Who Should Buy It?

Best For

  • Home welders using compatible MIG guns and 0.035-inch wire.
  • Workshop operators who replace contact tips regularly and want bulk spares.
  • Buyers who have confirmed their gun requires the specified M6 contact-tip geometry.

Skip If

  • Your welding gun requires a different thread, length, or tip series.
  • You primarily weld with another wire diameter and do not use 0.035-inch wire.
  • Your application requires a dedicated aluminum, heavy-duty, or other special-purpose contact tip.

How It Performs in Real Use

The following scenarios explain where the listed specifications are useful. They are based on the product details and common contact-tip functions, not independent hands-on performance testing.

1. Home Garage Welding

If you use a compatible MIG gun for repairs and small fabrication jobs, keeping spare contact tips can save time. When a tip becomes damaged by burnback or excessive wear, you can replace it with the correct part before returning to work.

The 30-piece package may provide more tips than an occasional welder needs immediately. Store unused pieces properly so they remain clean.

2. Routine Workshop Welding

In a workshop with repeated welding jobs, consumables may need regular inspection and replacement. Having 30 matching tips helps you keep replacement parts available for equipment that uses this exact specification.

The main benefit is spare-part availability. The listing does not provide controlled test results showing that these tips last longer than other copper tips.

3. Welding Training and Beginner Practice

Beginners can experience contact-tip damage while learning proper wire feeding, torch positioning, and arc control. A spare supply can be useful during supervised training.

However, replacing a tip will not correct poor machine settings, an incorrect wire-feed setup, or a damaged liner. Those problems need separate attention.

4. Long-Term Spare-Part Storage

Contact tips are small enough to organize in labeled containers. You can keep the 30-piece pack with your other consumables and take out replacements when needed.

Keep 0.035-inch tips separate from other sizes. Similar-looking tips can be difficult to identify once mixed together.

Installation and Setup Tips

Correct installation matters just as much as tip quality. Follow the instructions for your welding gun, especially when replacing consumables or inspecting the torch.

How to Replace a MIG Contact Tip

  1. Switch off the welder: Disconnect electrical power as directed by your equipment manual and allow the torch to cool fully.
  2. Remove the nozzle: Follow the gun manufacturer’s removal procedure.
  3. Remove the old contact tip: Use the appropriate tool if needed, taking care not to damage the gas diffuser.
  4. Inspect the parts: Look for damaged threads, excessive spatter, and other signs of wear.
  5. Confirm the replacement: Check the wire size, thread, and tip length before installation.
  6. Install the new tip: Start the threads carefully by hand, then tighten according to the gun manufacturer’s guidance. Do not overtighten.
  7. Reassemble the torch: Reinstall the nozzle and verify the setup before resuming welding.

Pro Tip: Keep one unused contact tip that matches your gun’s original specification as a reference. Compare its thread, length, and wire-size marking with new replacements before installing a bulk pack.

Common Installation Mistakes to Avoid

  • Forcing a contact tip into threads that do not match.
  • Using a 0.035-inch tip for a different wire size without checking manufacturer guidance.
  • Overtightening and damaging the tip or diffuser.
  • Installing a new tip without checking for a damaged diffuser or wire-feed problem.
  • Handling the contact tip before the welding gun has cooled.

Compatibility and Safety

Copper is commonly used for MIG contact tips because it conducts electrical current and heat. However, copper construction does not make a tip immune to damage from high temperatures, wear, or spatter.

Use these tips only in a welding gun with a compatible consumable system. Follow the machine and gun manuals for setup, wire selection, servicing, and safe operation.

Before maintenance, shut down the equipment according to the manufacturer’s instructions. Wear appropriate protective equipment for welding tasks, including proper eye, face, hand, and body protection.

If your torch shows damaged threads, loose electrical connections, or recurring burnback, inspect the full setup rather than repeatedly replacing contact tips. Seek qualified service when needed.

Cleaning, Maintenance, and Storage

When Should You Replace a Tip?

There is no verified fixed lifespan for this 30-pack. Tip life depends on welding conditions, wire movement, heat, machine setup, and operator technique.

Check the contact tip if you notice unstable electrical contact, repeated wire sticking, a visibly damaged opening, or burnback. These symptoms can also have other causes, so inspect the wire-feed system and other consumables.

Replace tips that are worn, badly damaged, or no longer suitable for reliable operation. Do not attempt to restore a seriously damaged tip by drilling or altering its bore.

How to Store Unused Tips

  • Keep the spare tips in a clean, dry container.
  • Label the container with the 0.035-inch wire size and M6 specification.
  • Protect the threads and tip openings from impacts and contamination.
  • Keep different tip sizes in separate compartments.
  • Inspect unused tips before installation if they have been stored for an extended period.

Customer Feedback and Warranty Details

Customer ratings can change as buyers submit new feedback.

That rating provides general buyer context, but it does not prove a particular service life, manufacturing tolerance, or compatibility with every listed welding gun. Your results will depend on the correct fit and welding conditions.

Returns and Manufacturer Warranty

Amazon displayed a 30-day refund or replacement option for the listing at review time, subject to the applicable return conditions. This should not be confused with a separate manufacturer warranty.

A distinct manufacturer warranty term was not confirmed. Check the current Amazon listing and seller information for any updated return or warranty details before purchasing.

Our Review Method

This editorial review uses the available product listing, stated specifications, and contact-tip compatibility information. We also considered the practical fit requirements of M6 threaded MIG consumables.

We did not conduct an independent welding endurance test or verify every supported gun configuration through physical installation. Performance comments describe expected use and limitations, not measured laboratory results.

Pros and Cons

Pros

  • 30 replacement tips in one package.
  • Copper material provides good electrical conductivity.
  • Clearly listed 0.035-inch wire size.
  • M6 thread and approximate 24 mm length help with fit checks.
  • Useful spare supply for compatible home and workshop welding guns.

Cons

  • Not suitable for every MIG gun, even if it uses 0.035-inch wire.
  • Approximate 24 mm length may differ from some original 11-series tips.
  • No independently verified lifespan or performance advantage over genuine replacement tips.

Is It Worth the Price?

The Welding Knight 30-pack is best viewed as a bulk replacement option. If you use a compatible gun regularly, buying multiple contact tips together may be more convenient than ordering a small pack whenever you need replacements.

Its value depends on the current package price and how often you replace tips. Divide the displayed package price by 30 to compare the cost per tip against genuine Lincoln, Tweco, or other compatible alternatives. Factor in shipping and any differences in material or tip design.

This set is worth considering if you want everyday replacement consumables and have already confirmed the fit. It is less attractive if you need only one or two tips, require special-purpose consumables, or remain unsure about compatibility.

How It Compares to Alternatives

Genuine Tweco 11-35 contact tips offer a documented 11-series specification for compatible Tweco equipment. Lincoln Electric KP11-35 contact tips are another option for supported Magnum gun configurations. These manufacturer-specific parts may be a better choice when you want to follow an original equipment replacement specification.

The Welding Knight pack stands out for its 30-piece quantity and advertised compatibility across several gun families. Before choosing it over original-brand tips, compare thread dimensions, overall length, required tip position, and total cost. A lower cost per tip is useful only when the replacement fits and works correctly.

Frequently Asked Questions

How Do I Properly Install the Contact Tips?

Switch off and safely isolate your welder, then let the gun cool. Remove the nozzle and old tip according to your gun manual, verify the new tip’s specifications, and install it without forcing or overtightening the threads. Reassemble the gun before returning to service.

Can These Tips Be Used With Other Welding Machines?

Possibly, but the contact-tip system matters more than the welder’s brand name. Your MIG gun must accept the correct wire size, M6 threading, and tip length. Check your gun’s consumable part number rather than assuming every MIG machine uses the same tips.

What Is the Expected Lifespan of These Contact Tips?

No fixed lifespan has been verified for this pack. Replacement frequency depends on operating conditions, heat, wire feeding, and tip wear. Inspect the tip regularly and replace it when damage or wear affects proper operation.

Are These Tips Suitable for Aluminum Welding?

The listing does not establish that these tips are optimized for aluminum wire. Some aluminum MIG setups require special contact tips or different clearances to account for wire feeding and thermal expansion. Follow your gun and wire manufacturer’s recommendations instead of assuming standard steel-wire tips are suitable.

How Should I Store the Contact Tips When Not in Use?

Keep unused tips in a clean, dry, labeled container. Protect the threads and openings from damage, and separate them from tips made for other wire diameters. Inspect each tip before installing it.

How Many Contact Tips Are Included?

The verified product listing specifies 30 contact tips. They are listed for 0.035-inch welding wire, so this is not a mixed-size assortment. Check the selected listing variation before ordering.

Are These Tips Compatible With the Lincoln Magnum 100L?

The Welding Knight listing names the Lincoln Magnum 100L as a compatible gun. However, you should still check the required original tip, its dimensions, and your gun’s configuration. Lincoln’s KP11-35 is a documented 0.035-inch replacement reference for certain Magnum 100L configurations.

Will New Contact Tips Fix Poor Wire Feeding or Burnback?

Replacing a worn or damaged contact tip may help when the tip is the source of the problem. Wire feeding issues can also result from incorrect settings, drive-roll problems, liner wear, or other equipment faults. Inspect the full wire-feed path if problems continue after installing a correctly sized tip.

The Bottom Line

The Welding Knight MIG Welding Contact Tips 15AK 11-35 30-pack is a practical option for welders who use 0.035-inch wire and have confirmed the required M6 tip geometry. Its copper construction and bulk quantity make it a useful spare-part choice, but you should skip it if your torch requires different dimensions or specialized consumables. Overall, it earns a recommended with compatibility checks verdict.

Ready to Buy?

Confirm the tip specifications and check the latest price and product details before ordering.

Check Price on Amazon โ†’

Leave a Comment