A concise assessment of the Power Stop SSH871 brake shoes highlights build quality, stopping feel, and fitment for 2005–2022 Toyota Tacomas. Constructed from 100% new rust‑resistant steel, with semi‑metallic friction compound, they promise firm initial bite, progressive modulation, low dust, and fast bedding; lining thickness is typically 10–12 mm at shipment. Installation includes all hardware; expect a 1–1.5 hour rear drum service per side. Questions about wear rates or compatibility?
Key Takeaways
- SSH871 shoes are 100% new rust-resistant steel with semi-metallic, post-cured friction compound for durability.
- Fitment: includes two rear shoes plus full spring, hold-down, and adjuster kit for 2005–2022 Toyota Tacoma.
- On-road: firm initial bite, progressive modulation, minimal dust, and short 50–100 mile break-in.
- Durability: resists fade under moderate towing; inspect linings and replace at 2–3 mm remaining.
- Installation: bolt-on readiness with plug-and-play alignment; use proper spring tool and follow axle torque 70–85 lb-ft.
Design and Construction Details
Construction and materials are the foundation of the SSH871 brake shoes. The shoes use 100% new steel, coated to resist rust, and a semi-metallic friction compound that is post-cured for durability.
Construction and materials define the SSH871 shoes: new rust-resistant steel and a post-cured semi-metallic friction compound for lasting durability
What are dimensions? Typical shoe height ~80–90 mm, lining thickness ~10–12 mm; check fit for Tacoma (2005–2022). Included hardware: springs and hold-down kits, torque specs per vehicle manual.
How to assess longevity? Inspect for uneven wear, measure lining down to 2–3 mm before replacement.
Installation is bolt-on ready; expect a 1–2 hour rear brake service per axle for a competent DIYer.
Performance and On-Road Experience
Having covered build and sizing, attention now turns to how the SSH871 brake shoes behave on the road. The reviewer notes firm initial bite, progressive modulation, and consistent stopping distance under mixed loads.
What to expect, in focused points:
- Short break-in: roughly 50–100 miles to reach ideal friction, minimal dust and quick bedding.
- Noise and feel: chamfered edges reduce chatter; occasional light squeal under cold, wet starts.
- Durability and heat: semi-metallic compound resists fade up to moderate towing, recommended for routine hauling, not extreme track duty.
Practical note: monitor lining wear every 5,000 miles.
Installation and Included Hardware
Start by laying out the included parts and evaluating fitment: the SSH871 set ships with two rear brake shoes, a full spring and hold‑down hardware kit (return springs, hold‑down pins and cups, and an adjuster / star wheel assembly), all sized for Toyota Tacoma rear drum assemblies from 2005–2022.
The reviewer notes bolt-on readiness, 0.75–1.25 inch shoe width, and plug‑and‑play hole alignment.
Reviewer highlights: bolt‑on readiness, 0.75–1.25″ shoe width, and exact plug‑and‑play hole alignment
Installation steps: remove drum, swap shoes, install springs, set star wheel.
Questions? Torque specs: 70–85 lb‑ft for axle nut, clean contact points.
Practical tip: use proper spring tool, measure drum runout ≤0.005 in. Liberation through competence.
Frequently Asked Questions
Do These Shoes Fit Non-Tacoma Toyota Models?
No — they fit Toyota Tacoma models (2005–2022) specifically. The speaker urges seekers to verify vehicle fitment via part numbers or VIN, reclaiming autonomy by choosing compatible parts rather than forcing ill-fitting substitutions.
Are They Compatible With Drum Parking Brakes?
Yes, they are compatible with drum parking brakes. The liberated enthusiast appreciates reliable, post-cured semi-metallic shoes, rust-resistant construction, chamfered edges for quiet operation, and included hardware enabling confident, straightforward installation and secure parking brake engagement.
What Is the Manufacturer’s Warranty Period?
Like a key releasing chains, the manufacturer provides a limited lifetime warranty. It empowers the buyer with coverage against defects for as long as ownership endures, promoting freedom from early-product failure concerns and restrictive replacements.
Do They Require Bedding-In Before Heavy Use?
No; they require minimal bedding-in before heavy use. The advanced semi‑metallic formula and post‑cure process shorten break‑in, empowering liberated drivers to quickly trust braking performance with reduced noise and reliable stopping power.
Are Replacement Lining Pads Available Separately?
Not exactly; replacement lining pads aren’t typically sold solo — customers may seek compatible aftermarket linings or consider full shoe replacements to regain braking freedom, embracing modular options or independent suppliers for tailored restoration and longevity.
Conclusion
In short, the Power Stop SSH871 brake shoes deliver expected results: 100% new rust‑resistant steel, semi‑metallic linings, and fit for 2005–2022 Toyota Tacoma rears. Stopping is firm with progressive modulation, dust is low, bedding is quick. Installation includes full hardware, takes about 45–75 minutes per axle with basic tools. Cost is reasonable for the materials and life expectancy. Want longevity? Monitor lining wear every 5,000 miles and replace before 2–3 mm remaining.
